ASTM A788 PDF

ASTM A Standard Specification for Steel Forgings, General Requirements. to steel forgings under any of the following specifications issued by ASTM. This standard is issued under the fixed designation A/AM; the number . 1 ASTM Standards:3 A/AM Specification for Alloy Steel Forgings for. ASTM A/AMb. Standard Specification for Steel Forgings, General Requirements. standard by ASTM International, 11/01/ View all product details.

Author: Gardagar JoJodal
Country: Cape Verde
Language: English (Spanish)
Genre: History
Published (Last): 19 May 2005
Pages: 141
PDF File Size: 20.80 Mb
ePub File Size: 6.1 Mb
ISBN: 603-9-81968-300-7
Downloads: 57451
Price: Free* [*Free Regsitration Required]
Uploader: Yozshusida

The following items shall be reported: Tension and hardness tests shall be conducted to evaluate mechanical properties such as percentage of elongation and reduction of area.

Repair welding shall not be allowed unless permitted by the product specification. An example of the determination of a weighted average analysis for an ingot made from a three-heat combination pour with varying weights and chemistry involved in each heat is shown below: Details of heat and product analyses for the evaluation of chemical composition are thoroughly discussed with the expertise.

In modern times, industrial forging is done either with presses or with hammers powered by compressed air, electricity, hydraulics or steam.

Test each specimen at a different temperature such that the percentage of shear fracture will be both above and below the value of n, but within a range of Link to Active This link will always route to the current Active version of the standard.

Vacuum Carbon Deoxidation S9.

ASTM A / AM – 18b Standard Specification for Steel Forgings, General Requirements

It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. The area shall be taken in the most unfavorable location relative to the indications being evaluated. The steel producer shall remove the transition material by any established procedure that positively separates the grades.

The analysis may also be taken from a mechanical test specimen or the mechanical test location as de? Intercritical Heat Treatment S4. The listed variation value is subtracted from the minimum speci? Such cycles shall be followed by tempering within the temperature limits required by the material speci?

  COMO DEFENDERSE DE LOS ATAQUES VERBALES BARBARA BERCKHAN PDF

Permissible Variation Over the Speci? Any straightening performed before heat treatment for properties does not require an intermediate stress-relief heat treatment. The capacity of the system must also be sufficiently high to reduce the initial surge pressure at the start of the pour to a low level within 2 min.

ASTM A788 Stainless Steel Forged Fittings Suppliers

Steel Forgings, Alloy, for Carburizing Applications. Samples for analysis may be taken from the forging or from a full-size prolongation at any point from the midradius to the outer surface of disk or other solid forgings or midway between the inner and outer surfaces of hollow or bored forgings. The number, orientation and location of the tests shall be speci?

This specification covers a group of common requirements that, unless covered by the individual product specification in another ASTM document, applies to steel forgings for general use.

Siddhagiri Metals and Tubes Rating: Steel shall be forged by any of these three classes based on forging temperature: Tension and hardness tests shall be conducted to evaluate mechanical properties such as the percentage of elongation and reduction of area.

Sequential or Continuous Strand Casting S3. The results of the method used shall conform to the requirements of the product speci? Heat Analysis for Remelted Ingots S Work Item s – proposed revisions of this standard. Superstrength Alloy Steel Forgings. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

One or more molds can be set up on asfm individual plate, and more than one plate may be poured in sequence from a heat. Traditionally, forging was performed by a smith using hammer and anvil, w788 introducing water power in the production and working of iron in the 12th century which allowed the use of large trip hammers or power hammers that exponentially increased the amount and size of iron that could be produced and forged easily.

ASTM A – 02 Standard Specification for Steel Forgings, General Requirements NO_PDF

Required information including test temperature, conditioning, environment, and acceptance criteria shall be provided as necessary.

  GANESH VASANTH NOVELS PDF

The acceptance of any such additional requirements shall be dependent on negotiations with the supplier and must be included in the order. Charpy Impact Tests S We have a large inventory of Stainless Steel Forged Fittings which have high tensile strength and provide excellent resistant to corrosion.

If the choice of test track is not made in the ordering information then the default ASTM track shall be used as noted in Test Methods A This suffix shall not be removed until the material speci? The penetrant system to be used shall be agreed upon between the manufacturer and purchaser. These elements are considered as incidental and may be present to the following maximum amounts: It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Packaging and Package Marking The primary melting may incorporate separate degassing or refining and may be followed by secondary melting, using electro slag ESR or vacuum arc remelting VAR.

Cooling Prior aatm Heat Treatment 7. The evacuation system shall be capable of reducing the pressure asgm, which occur each time a new portion of steel is admitted to the vessel to increasingly lower levels, until a blank-off pressure usually less than ?

Wrought Carbon Steel Wheels. Open-ended molds, which are usually cooled and used, for example, in the continuous casting of steel, are considered to be included in this de? The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. The outside diameter may be contoured if required. Each of the retested specimens must exhibit an energy value equal to or greater than the minimum average value required by the product speci?

Straightening of Forgings Adtm. Magnetic Particle Examination S