ATMEL 24C04 PDF

each, the 16K requires an bit data word address for random word addressing. WP Pin. Status. Part of the Array Protected. 24C01A. 24C 24C 24C08A. 24C04 EEPROM are available at Mouser Electronics. Mouser offers For: 24C Obsolete. Microchip Technology / Atmel, EEPROM 7 MILS V – 10MS V. Read about ’24C04 Interfacing issue’ on elementcom. Hey there,I am trying to interface the AT24C04 4K EEPROM with Atmega

Author: Torn Nitilar
Country: Kenya
Language: English (Spanish)
Genre: Photos
Published (Last): 6 October 2004
Pages: 404
PDF File Size: 2.50 Mb
ePub File Size: 19.19 Mb
ISBN: 434-3-47163-796-8
Downloads: 42736
Price: Free* [*Free Regsitration Required]
Uploader: Faujas

A2 are used for creating the address. Post as a guest Name.

Sign up using Facebook. Post Your Answer Discard By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies. The information in this document is provided in connection with Atmel products.

Full 2K Array 24C04 1. Also be aware that the A0 to A2 pins on the device package are meant to remain static in a design. In Arduino, the function that does this is digitalWrite.

How to connect / use ATMEL 24C16 EEPROM chip?

No license, express or implied, by estoppel or otherwise, to any. Home Questions Tags Users Unanswered. Then when you want to write to the part use an address byte of 0xA0 and when you want to read use an address byte of atmfl. Then the address byte that you use to write to the second chip would be 0xA2 and the address byte for reading the second chip would be 0xA3. Atmel Corporation makes no warranty for the usedetailed in Atmel ‘s Terms and Conditions located on the Company’s web site.

  ASIS POA MANUAL PDF

But my suggestion would to directly connect them to ground or VCC for the addressing scheme.

It considers the value of the A0,A1 and A2 before the power up and sticks to it till reset. TurboJ The chip says the following: The Company assumes no. Atmel Corporation makes no warranty for the use. Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in. Can you give more information? Aymel the issue is setting the address after power on.

In figure 4 they refer to the address as an 8-bit quantity:. On top of that I have never been sure that it is even possible to dynamically change the strapped value on the A0, A1 and A2 pins of a 24C02 after it has powered up.

10pcs AT24C04 24c04 Serial EEPROM Sop-8 Atmel

This device is not recommended for new designs. Is there something else I need to do? Then the address byte that you use to write to the third chip would be 0xA4 and the address byte for reading the second chip would be afmel. Email Required, but never shown.

If you just have one 24C02 then you would connect all three of those pins to GND as b. That’s why I said “write”.

24C04 Atmel ATMEL ORIGINAL

Normally there is no writing to the 24C02 pins. MO footprint tai 24c02 atmel 24c02 atmel 24c04 tai 24c04 at24c01atsi pin configurations of 24c04 1 24c04 Atmel atmel 24c16 Text: This output is from I2C scanner. Are you being confused by the common mistake that many people make where they treat the address of an I 2 C wrongly?

  ANTON PANNEKOEK LENIN FILOSOFO PDF

RoomJapan Atmel Japan K. By clicking “Post Your Answer”, you acknowledge that you have read our updated terms of serviceprivacy policy and cookie policyand that your continued use of the website is subject to these policies. The device will not respond to the address that is being set dynamically. The information in this document is provided in connection with Atmel.

Instead the three bits that you supply out on the interface in the device address field must match the hard strapped values on the pins in order for the device to be selected.

Can you explain what hardwiring 2c404 Previous 1 2 It connects the SOT package pins to the same signal position of the 8 pin DIPmechanical and electrical connections are supported by this adapter.

Writing to a serial EEPROM Atmel 24C04 in Labview – Discussion Forums – National Instruments

It will answer to address that was set up before powering up. In figure 4 they refer to the address as an 8-bit quantity: Please refer to AT24C08A.

If a total of eight 24C02’s are used in the design then each of the devices will have these three pins hard strapped in a different combination from the set of b, b, b, b, b, b, b and b. When you say that you are “writing” to the pins this does not make clear exactly what you are doing. Can’t change the values dynamically.