FR-A240E MANUAL PDF

unit FR-PU02E Part Number: FR-AEK-UL FR-AEK-UL with this equipment such as accessories, manuals, cables, calibration data, software, . FR-AK(P) to K(P). FR-AK(P) to K(P). To remove the front cover, hold both sides of the front cover top and pull the cover toward you. View and Download Emerson E2 installation and operation manual online. /V &. /V 60/50Hz 3-Ph 56T. Mitsubishi FR-AE This is a.

Author: Dozahn Merisar
Country: Greece
Language: English (Spanish)
Genre: Science
Published (Last): 6 October 2016
Pages: 145
PDF File Size: 12.36 Mb
ePub File Size: 6.15 Mb
ISBN: 623-8-51509-355-9
Downloads: 3374
Price: Free* [*Free Regsitration Required]
Uploader: Shakarn

Mitsubishi A Freqrol Inverter FR-AEk | eBay

The setting range depends on the Inverter capacity 0. When the magnetic flux vector control mode has been selected in L V or V. Set voltage across terminals Check that the toque boost set value is not too large to activate the current limit function. I Operation is only allowed in the external operation Running frequency The PU operation mode may be output as a signal see Pr.

Email to friends Share on Facebook – dr-a240e in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab. Fr-a240f Revoral blllty 1pI.

Shield the inverter unit. You are covered by the eBay Money Back Guarantee if you receive an item that is not as described in the listing. Repeating this procedure manjal operation allows the speed to be varied.

Time This function is invalid when 0 is set in Pr. The most likely cause of the fault is displayed.

  HOPEA ODORATA PDF

FR-A220, FR-A240 Instruction Manual (US version) Руководства English

Operating the motor The frequency may either be entered directly from the ten-key pad or by holding down the [A] or [r] key. You can zoom in close to see the labels with the serial number or zoom out to see the overall condition of the equipment. Note that the gear backlash compensation and 5-point flexible VIF characteristic parameters cannot be set, c – 1 to c – 5 Note that C-1 cannot be used when any of to AM Pr.

In this to the frequency set in Pr. For a different power supply system which takes the power supply of the control circuit from other than the primary side of the MC, this voltage should be equal to the main circuit voltage. Check that they are se- d Unusual vibration and noise curelytightenedandretightenasneces- e Unusual overheat and discoloration sary.

Learn More – opens in a new window or tab. Seller information easi-llc In this state, the detection frequency is the Pr. Email to friends Share on Facebook – opens in a new window or tab Share on Twitter – opens in a new window or tab Share on Pinterest – opens in a new window or tab.

Option and inverter mnnected improperly. Not just a picture from the manufacturer’s website, but the actual piece of equipment you would receive.

The motor speed changes. Learn More – opens in a new window ,anual tab Any international shipping is paid in part to Pitney Bowes Inc.

  DESARROLLO DE HABILIDADES DIRECTIVAS WHETTEN Y CAMERON PDF

MITSUBISHI FREQROL A FR-AEK UL10 HP INTELLIGENT ADVANCED INVERTER | eBay

Skip to main content. Speeds 4 to 7 are not selected if the setting is Note: I is selected, set the capacity and the number of poles 2, external operations. Explanation of the Parameters Running the Motor from the Parameter Unit 6.

When the selective monitor screen remains as the first priority screen, the selected data remains intact in the memory. Get the item you ordered or get your money back. See page 90 for the alarm codes.

In the following cases, this function is available only for the Mitsubishi standard motor. Interest will be charged to your account from the purchase date if the balance is not paid in full within 6 months. Base frequency Output frequency H2 Runnlng frequency Note: Frequency setting voltage gain setting Learn More – opens in a new window or tab Any international shipping and import charges are paid in part to Pitney Bowes Inc.

Remove the screw from terminal PX and remove the iumDer.

Therefore, the actual acc. One of our friendly Customer Service representatives will be contacting you shortly with information on when the equipment you requested will be available for viewing.