ISO 14577-2 PDF

des machines d’essai. STANDARD. ISO. Second edition. . Reference number. ISO (E). Provläsningsexemplar / Preview. ISO. First edition. Metallic materials — Instrumented indentation test for hardness and materials parameters —. Part 2: Verification and . ISO is an international standard that governs instrumented indentation [1]. ISO , Part 1, prescribes the procedure and data analysis, and.

Author: Samugor Kagaramar
Country: Tajikistan
Language: English (Spanish)
Genre: Health and Food
Published (Last): 26 September 2014
Pages: 325
PDF File Size: 4.96 Mb
ePub File Size: 3.14 Mb
ISBN: 570-7-49677-928-8
Downloads: 70838
Price: Free* [*Free Regsitration Required]
Uploader: Shaktigal

Verification and calibration of testing machines ISO ISOMetallic materials — Calibration of force-proving instruments used for the verification of uniaxial testing machines.

EVS-EN ISO – Estonian Centre for Standardisation

There is a requirement that the indirect method be used in addition to the direct method and for the periodic routine checking of the testing machine in service. ISO specifies the method of verification and calibration of testing machines for carrying out the instrumented test iiso accordance with ISO Metallic materials – Instrumented indentation test for hardness and materials parameters – Part 3: Calibration of reference blocks ISO Pile-up generally occurs for fully work-hardened materials.

These surface effects result in an under-estimate pile-up or over-estimate sink-in of the contact area 144577-2 the analysis and hence may influence the measured results.

Test method ISOMetallic materials — Instrumented indentation test for hardness and materials parameters — Part 3: The method assumes that coating properties are constant with indentation depth. It has been reported that the piled up material results in an effective increase of the contact area for the determination of hardness, while the effect is less pronounced for the determination of indentation modulus, since the piled up material behaves less rigidly.

  ELECTRIC DRIVES ION BOLDEA PDF

Limits for such cases are given. Test method for metallic and non-metallic coatings.

ISO 《金属材料 硬度和材料参数的仪器化压痕试验 第2部分:试验机的检验和校准》国际标准(英文版)

Certified by ISO Related international standards This standard is identical to: Les mer om abonnement. Metallic materials – Instrumented indentation test for hardness and materials parameters – Part 1: Verification and calibration of testing machines.

The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application.

Use of Atomic Force Microscopy AFM to assess the indent shape allows the determination of possible pile-up or sink-in of the surface around the indent. Scope This part of ISO specifies the method of verification and calibration of testing machines for carrying out the instrumented indentation test in accordance with ISO Test method ISO Fordelene med et abonnement: ISOMetallic materials — Instrumented indentation test for hardness and materials parameters — Part 3: For undated references, the latest edition of the referenced document including any amendments applies.

  INCRUSTACIONES ONLAY E INLAY PDF

The hardness of visco-elastic materials or materials exhibiting significant creep will be strongly affected by the time taken to perform the test. It is a requirement that the indirect method of verification of the testing machine be carried out independently for each test method. Metallic materials – Instrumented indentation test for hardness and materials parameters – Part 2: Forside Nettbutikk Produktkatalogen Produktpresentasjon.

ISO 14577-4:2016

About Us Info center Standardization. NOK 1 ,00 eks. Test method ISO Metallic materials – Instrumented indentation test for hardness and materials parameters – Part 4: This part of ISO is also applicable for transportable testing machines. Calibration of reference blocks.

Composite coatings are considered to be homogenous if the structure size is less than the indentation size. For dated references, only the edition cited applies.

FAQ What is standard Become a member? Verification and calibration of testing machines ISO This part of ISO specifies the method of verification and calibration of testing machines for carrying out the instrumented indentation test in accordance with ISO My account Shoping cart 0 Help.