I have been looking everywhere for a M16A4/ACOG TA01NSN 4×32 standard GI 25meter zero target. I have seen them online but can’t find. Designed for the M4/M16A4, the ACOG provides an “auto ranging” reticle for ranges When a target is acquired, use the ranging reticle (if time allows) to get an Without the aid of references, demonstrate the two methods to zero the ACOG. feedback (Figure 10). The M Sight, RCO, when installed on a M4/M4A1/ M16A4/M16A2, is zeroed on a standard M16 zero target with alternate strike points.

Author: Tojagore Kazirisar
Country: Namibia
Language: English (Spanish)
Genre: Medical
Published (Last): 21 October 2012
Pages: 98
PDF File Size: 7.82 Mb
ePub File Size: 18.8 Mb
ISBN: 873-7-79151-603-5
Downloads: 60985
Price: Free* [*Free Regsitration Required]
Uploader: Garn

Already have an account? Although some courses of fire may seem redundant or tarbet, numerous tests show that these training strategies work and the qualification standards are achievable if the strategy is followed.

No centering or focusing is required.

Extensive testing has proven that the average soldier does not properly use the night vision devices. Weapon stability is crucial in boresighting. The procedures are the same as standard iron sight procedures. As armorer said definetly tagget out to yards if possible for better accuracy, and I personally use an A. The procedures for record qualification are:.

My self-made zeroing target for m. I somehow was not confident in that and zeroed my ACOG at m against all manuals by the way what will be “good” group size at this range for standard and very used M4?

Wherever the gipsies take me. With the vehicle not moving, the tires are cold. A good example is the tire on a vehicle. Per ACOG usage, top of the chevron is where you should aim. I axog to get a real Trijicon Yes, my password is: I usually don’t have much time to fine tune further.


When the soldier is ready to fire, the elbows are firmly planted on the ground to prevent the laser from wobbling excessively. At m it’s more accurate. Lay the weapon on the rucksacks and then lay another rucksack on top of the weapon to stabilize it.

25 Meter Zeroing Targets | The Weapon Blog

Practice qualification standards for the BIS are the same as with standard iron sights. If a borelight is not available, a meter zero must be done to zero the device. Figure shows the current training program for these lasers. Many forget you looking for hits on target with a ar as intended use. Log in tsrget Sign up. Oct 17, Messages: This basically is for service rifle set up but you can apply it to any AR A2 style rear sight.

25 Meter Zeroing Targets

The weapon should be in the “bolt forward” position and must not be canted left or right during boresighting procedures. They are the same weapon sight, different reticule. Question for those who might know. Sign In Sign Out.

FM Appendix G Meter Target Offsets And Meter Zero Offsets

The engine compartment, exhaust, and tires of a vehicle that has been moving are all examples of thermal cues. Is there manual like this also for TA31??? Aim the red dot of the M68 on the crosshair located on the meter boresight target. Regardless of the qualification, the standard day record fire for the iron sights tarbet be used.

I know what manual zro are talking about. Help out a brother Block When you block a person, they can no longer invite you to a private message or post to your profile wall.

Ok I know its pre-alpha and some stuff is there for placeholder and testing but im wondering where do the bullets go in pre-alpha? Premium Membership Required Access to this requires a premium membership. I picked up that from a post under the rifle competition section Regular blinking during scanning relieves some of the eyestrain that the soldier tends to have trying to spot far targets.


The zeroing standards for the BIS are the same as with iron sights.

So, your point of aim would be the center of the main crosshairs and you would adjust elevation top screw. Do you already have an account? During the dry-fire exercise, soldiers acquire a sight picture on all exposed silhouette targets before conducting the field-fire scenario.

The thing is that in IDF we zero ACOG’s in the way when far zero is at m close is smthng like 37m, i’m not sure and i’m suspicious about: It works as intended. Dry fire is done to allow the soldiers to make adjustments to the TWS. In my manual it said to zero at 36m with the tip of the post that was inside of the chevron.

Confirm that equipment is tight prior to zeroing. Other procedures are the same as standard iron sight procedures. Found this in Trijicon’s manual cause I needed reading material. The soldier must keep the rifle and M68 in a vertical alignment each time he fires. We’re getting ready to get them out zeero the range, and need some fresh info.

The Acoh is a thermal sight and does not require the use of night vision devices. The back-up iron sights BIS can be boresighted to a new user to expedite meter zeroing.